Plug a VT100 terminal (or terminal emulator) into the Pipeline 130's serial port. (9600 baud, 8 Bits, No parity, 1 Stop bit).
When the Pipe 130 powers up, you'll see this on your VT100 display. You may need to type a control-L to repaint your screen.
----------- EDIT ----------- ------------------- ------------------- |Configure... | |10-100 1 T1/CSU | |00-200 00:00:13 | |>Switch Type=AT&T/P-T-P ^| | Link X RED | |>M31 Line 00 Ch | | Chan Usage=Switch/Switch | | B1 . | | Call Connected | | My Num A= | | B2 . | | | | My Num B=N/A | ------------------- ------------------- | SPID 1=N/A | |20-100 Sessions | |20-500 DYN Stat | | SPID 2=N/A | |> 0 Active | | Qual N/A 00:00:00| | Ans Voice Call=Yes | | | | 0K 0 channels| | My Name= | | | | CLU 0% ALU 0%| | My Addr=0.0.0.0 | ------------------- ------------------- | Rem Name= | |20-300 WAN Stat | |20-400 Ether Stat | | Rem Addr= | |>Rx Pkt: 0^| |>Rx Pkt: 0| | Dial #= | | Tx Pkt: 0 | | Tx Pkt: 0| | Route=No | | CRC: 0v| | Col: 0| | Bridge=No | ------------------- ------------------- | Send Auth=None | |00-100 Sys Option | |00-400 HW Config | | Send PW=N/A | |>Security Prof: 1 ^| |>BRI Interface | | Recv Auth=None | | Software +6.0.0+ | | Adrs: 00c07b5a5c17| | Recv PW=N/A v| | S/N: 613xxxx v| | Enet I/F: UTP | Press Ctrl-n to move cursor to the next menu item. Press return to select it. Press Tab to move to another window --- thick border indicates active window.
To configure the router, use the arrow keys to descend the menu tree to the section and value you wish to change and update the value. To save the change(s), use the left arrow to get:
----------- EDIT ----------- |EXIT? | |>0=ESC (Don't exit) | | 1=Exit and discard | | 2=Exit and accept | Select "Exit and accept" to save the change(s).
Be sure the Pipeline 130 is running software version 6.0.2 or newer. The implementations of NAT in earlier versions does not work correctly. Current versions of Pipeline code are available from the Ascend web Ascend web page or from the EasyStreet tftp server at tftp.easystreet.com:/P130
To use this configuration information you only need to change the values shown in color. There are about 55 values that need to be changed from the factory defaults.
Insert the value issued by EasyStreet
Insert the value issued by the telephone company
Insert a value of your choosing
Insert the value as displayed on this page
Clear Current Configuration:
control-D D
> fclear . > nvram (Router will reset with factory default configuration)
--------------- EDIT --------------- |Main Edit Menu | |>Configure... | | 00-000 System | | 20-000 Ethernet | | 30-000 Nailed T1 | | |
Configure...
--------------- EDIT --------------- |Configure... | |>Switch Type=AT&T/P-T-P | | Chan Usage=Switch/Switch | | My Num A= | | My Num B=N/A | | SPID 1=N/A | | SPID 2=N/A | | Ans Voice Call=Yes | | My Name=Router Name | | My Addr=192.168.1.1/24 | | Rem Name=EasyStreet FR | | Rem Addr=EasyStreet Serial IP/30 | | Dial #= | | Route=IP | | Bridge=No | | Send Auth=None | | Send PW=N/A | | Recv Auth=None | | Recv PW=N/A | | Save= |
System -> Security
-------- ROUTERNAME-GW EDIT -------- |00-300 Security | | 00-301 Default | | 00-302 | |>00-303 Full Access | | |
System -> Security -> 00-302
-------- ROUTERNAME-GW EDIT -------- |00-302 | Note: SET THE 00-302 PASSWORD FIRST | Name=Router Name | |>Passwd=Router Password | | Operations=Yes | | Edit Security=Yes | | Edit System=Yes | | Field Service=Yes |
System -> Security -> Default
-------- ROUTERNAME-GW EDIT --------
|00-301 Default |
| Name=Default |
| Passwd= |
|>Operations=No |
| Edit Security=N/A |
| Edit System=N/A |
| Field Service=N/A |
System -> Security -> Full Access
Note: You'll need to authenticate yourself now
control-D P select Router Name type in the Router Password -------- ROUTERNAME-GW EDIT -------- |00-303 Full Access | | Name=Full Access | |>Passwd=PASSWORD | | Operations=Yes | | Edit Security=Yes | | Edit System=Yes | | Field Service=Yes |
Ethernet -> Connections -> EasyStreet FR
-------- ROUTERNAME-GW EDIT --------
|20-101 EasyStreet FR |
| Station=EasyStreet FR |
| Active=Yes |
|>Encaps=FR |
| Dial #=N/A |
| Alt Dial #1= |
| Alt Dial #2= |
| Alt Dial #3= |
| Calling #=N/A |
| Called #=N/A |
| Route IP=Yes |
| Route IPX=N/A |
| Bridge=No |
| Dial brdcast=N/A |
| Encaps options... |
| Ip options... |
| Ipx options... |
|>Session options... |
| Telco options... |
Ethernet -> Connections -> EasyStreet FR -> Encaps options...
-------- ROUTERNAME-GW EDIT --------
|20-101 EasyStreet FR |
| Encaps options... |
| >FR Prof=EasyStreet FR |
| DLCI=16 |
Ethernet -> Connections -> EasyStreet FR -> Ip options...
-------- ROUTERNAME-GW EDIT -------- |20-101 EasyStreet FR | | Ip options... | | >LAN Adrs=EasyStreet Serial IP/30 | | WAN Alias=0.0.0.0 | | IF Adrs=192.168.1.1/24 | | Preference=60 | | Metric=1 | | DownPreference=120 | | DownMetric=7 | | Private=No | | RIP=Off | | Client Pri DNS=0.0.0.0 | | Client Sec DNS=0.0.0.0 | | Client Assign DNS=No | | Client Gateway=0.0.0.0 |
Ethernet -> Filters -> IP Call
Note: The following filter fixes an Ascend security bug.
-------- ROUTERNAME-GW EDIT --------
|20-401 IP Call |
|>Name=Discardfilter |
| Input filters... |
| Output filters... |
Ethernet -> Filters -> Discardfilter -> Input filters... -> In filter 01
-------- ROUTERNAME-GW EDIT --------
|20-401 Discardfilter |
| In filter 01 |
| >Valid=Yes |
| Type=IP |
| Generic... |
| Ip... |
| Ipx... |
Ethernet -> Filters -> Discardfilter -> Input filters... -> In filter 01 -> Ip...
-------- ROUTERNAME-GW EDIT -------- |20-401 Discardfilter | | Ip... | | >Forward=No | | Src Mask=0.0.0.0 | | Src Adrs=0.0.0.0 | | Dst Mask=0.0.0.0 | | Dst Adrs=0.0.0.0 | | Protocol=17 | | Src Port Cmp=None | | Src Port #=N/A | | Dst Port Cmp=Eql | | Dst Port #=9 | | TCP Estab=N/A |
Ethernet -> Filters -> Discardfilter -> Input filters... -> In filter 02
-------- ROUTERNAME-GW EDIT --------
|20-401 Discardfilter |
| In filter 02 |
| >Valid=Yes |
| Type=GENERIC |
| Generic... |
| Ip... |
| Ipx... |
Ethernet -> Filters -> Discardfilter -> Input filters... -> In filter 02 -> GENERIC
-------- ROUTERNAME-GW EDIT --------
|20-401 Discardfilter |
| Generic... |
| >Forward=Yes |
| Offset=0 |
| Length=0 |
| Mask=0000000000000000 |
| Value=0000000000000000 |
| Compare=Equals |
| More=No |
Ethernet -> Frame Relay -> 20-501
-------- ROUTERNAME-GW EDIT -------- |20-501 | |>Name=EasyStreet FR | | Active=Yes | | Call Type=Nailed | | FR Type=DTE | | LinkUp=Yes | | Nailed Grp=3 | | Data Svc=64K | | Dial #=N/A | | Link Mgmt=T1.617D | | N391=6 | | DTE N392=3 | | DTE N393=4 | | DCE N392=N/A | | DCE N393=N/A | | T391=10 | | T392=N/A | | MRU=1532 |
Ethernet -> NAT -> NAT...
-------- ROUTERNAME-GW EDIT -------- |20-A01 NAT... | | Routing=Yes | |>Profile=EasyStreet FR | | FR address=Customer Serial IP | | Static Mappings... | | Def Server=0.0.0.0 | | Reuse last addr=No | | Reuse addr timeout=N/A |
Ethernet -> NAT -> NAT... -> Static Mappings... -> Static Map 01
Note: This static mapping allows access to the router from EasyStreet
-------- ROUTERNAME-GW EDIT -------- |20-A01 NAT... | | Static Map 01 | | Valid=Yes | | Dst Port #=23 | | Protocol=TCP | | Loc Port #=23 | | >Loc Adrs=192.168.1.1 |
Ethernet -> NAT -> NAT... -> Static Mappings... -> Static Map 02
Note: This static mapping allows EasyStreet to gather SNMP statistics from the router
-------- ROUTERNAME-GW EDIT -------- |20-A01 NAT... | | Static Map 02 | | Valid=Yes | | Dst Port #=161 | | Protocol=UDP | | Loc Port #=161 | | >Loc Adrs=192.168.1.1 |
Ethernet -> NAT -> NAT... -> Static Mappings... -> Static Map 03
Note: If you have a mail server connected to the router's ethernet at 192.168.1.2 ...
-------- ROUTERNAME-GW EDIT -------- |20-A01 NAT... | | Static Map 03 | | Valid=Yes | | Dst Port #=25 | | Protocol=TCP | | Loc Port #=25 | | >Loc Adrs=192.168.1.2 |
Ethernet -> Mod Config
-------- ROUTERNAME-GW EDIT -------- |20-B00 Mod Config | |>Ether options... | | SNMP options... | | Route Pref... | | Bridging=No | | IPX Routing=No | | Shared Prof=No | | Telnet PW=Router Password | | RIP Policy=Poison Rvrs | | RIP Summary=Yes | | ICMP Redirects=Accept | | NAT Routing=Yes | | NAT Profile=EasyStreet FR | | BOOTP Relay... | | DHCP Spoofing... | | DNS... | | Multicast... | | Auth... | | Log... | | ATMP... | | UDP Cksum=No | | TCP timeout=0 | | Adv Dialout Routes=Always | | Reply DirectedBcast Ping=Yes | | Forward Directed Bcast=Yes |
Ethernet -> Mod Config -> Ether options...
-------- ROUTERNAME-GW EDIT -------- |20-B00 Mod Config | | Ether options... | | >IP Adrs=192.168.1.1/24 | | 2nd Adrs=Customer Serial IP/30 | | RIP=Off | | RIP2 Use Multicast=No | | Ignore Def Rt=No | | Proxy Mode=Off | | Filter=1 | | IPX Frame=None | | IPX Enet#=N/A | | IPX Pool#=N/A | | IPX SAP Filter=N/A | | IPX SAP Proxy=N/A | | IPX SAP Proxy Net#1=N/A | | IPX SAP Proxy Net#2=N/A | | IPX SAP Proxy Net#3=N/A | | Handle IPX Type20=N/A |
Ethernet -> Mod Config -> SNMP options...
-------- ROUTERNAME-GW EDIT -------- |20-B00 Mod Config | | SNMP options... | | >Read Comm=monitor | | R/W Comm Enable=Yes | | R/W Comm=read | | Queue Depth=0 |
Ethernet -> Mod Config -> DHCP Spoofing...
-------- ROUTERNAME-GW EDIT -------- |20-B00 Mod Config | | DHCP Spoofing... | | DHCP Spoofing=No | | >DHCP PNP Enabled=No | | Renewal Time=N/A | | Become Def. Router=N/A | | Dial if Link Down=N/A | | Always Spoof=N/A | | Validate IP=N/A | | Maximum no reply wait=N/A | | IP Group 1=N/A | | Group 1 count=N/A | | IP group 2=N/A | | Group 2 count=N/A | | Host 1 IP=N/A | | Host 1 Enet=N/A | | Host 2 IP=N/A |
Ethernet -> Mod Config -> DNS...
-------- ROUTERNAME-GW EDIT -------- |20-B00 Mod Config | | DNS... | | >Domain Name=customer.com | | Sec Domain Name= | | Pri DNS=69.30.0.200 | | Sec DNS=209.162.195.5 | | Allow As Client DNS=Yes | | List Attempt=No | | List Size=N/A | | Client Pri DNS=0.0.0.0 | | Client Sec DNS=0.0.0.0 | | Enable Local DNS Table=No | | Loc.DNS Tab Auto Update=No |
Main Edit Menu -> Nailed T1 -> Mod Config
-------- ROUTERNAME-GW EDIT --------
|30-100 Mod Config |
|>Nailed T1 Group=3 |
| Activation=Enabled |
| Framing Mode=ESF |
| Encoding=B8ZS |
| FDL=None |
| Build Out= 0 dB |
| First DS0=1 |
| Last DS0 =See Note Below |
| Clock Source=No |
| Loop Back=Normal |
Last DS0 = 1 thru 24. One for each 64kb channel of bandwidth
2 = 128kb
4 = 256kb
6 = 384kb
8 = 512kb
24 = Full T1
Reset the router after completing the configuration information.
control-D D
> reset
Allow 2 minutes for the Pipe130 to sync up with the frame relay switch and another 2 minutes for the EasyStreet router to detect the customers circuit come up.
After the circuit comes up, your should see the values noted in brown.
---- ROUTERNAME-GW EDIT ---- ------------------- ------------------- |Main Edit Menu | |10-100 1 T1/CSU | |00-200 03:01:12 | | Configure... | | Link X CARRIER | |>M31 Line Ch | | 00-000 System | | B1 . | | LAN session up | |>20-000 Ethernet | | B2 . | | EasyStreet FR | | 30-000 Nailed T1 | ------------------- ------------------- | | |20-100 Sessions | |20-500 DYN Stat | | | |> 1 Active | | Qual N/A 00:00:00 | | | | O EasyStreet FR | | 0K 0 channels | | | | | | CLU 0% ALU 0% | | | ------------------- ------------------- | | |20-300 WAN Stat | |20-400 Ether Stat | | | |>Rx Pkt: 5545 | |>Rx Pkt: 139 | | | | Tx Pkt: 1247 | | Tx Pkt: 380 | | | | CRC: 0 | | Col: 0 | | | ------------------- ------------------- | | |00-100 Sys Option | |00-400 HW Config | | | |>Security Prof: 3 | |>BRI Interface | | | | Software +6.0.0+ | | Adrs: 00c07bsd5c1f| | | | S/N: 613xxxx | | Enet I/F: UTP |
Next go to the terminal server screen and try some pings. You may need to authenticate yourself.
control-D E=Termsrv Ascend Pipeline Terminal Server ** ascend% ping 69.30.0.200 PING 69.30.0.200 (69.30.0.200): 56 data bytes 64 bytes from 69.30.0.200: icmp_seq=0 ttl=254 time=30 ms 64 bytes from 69.30.0.200: icmp_seq=1 ttl=254 time=20 ms 64 bytes from 69.30.0.200: icmp_seq=2 ttl=254 time=20 ms ^C --- 69.30.0.200 ping statistics --- 3 packets transmitted, 3 packets received, 0% packet loss round-trip min/avg/max = 20/23/30 ms
(control-C will terminate the ping command)
ascend% ping yahoo.com
PING yahoo.com (204.71.177.35): 56 data bytes
64 bytes from 204.71.177.35: icmp_seq=0 ttl=249 time=40 ms
64 bytes from 204.71.177.35: icmp_seq=1 ttl=249 time=50 ms
64 bytes from 204.71.177.35: icmp_seq=2 ttl=249 time=40 ms
^C
--- yahoo.com ping statistics ---
3 packets transmitted, 3 packets received, 0% packet loss
round-trip min/avg/max = 40/43/50 ms
You've now tested connectivity to both EasyStreet and the InterNet and verified that nameservice is working for your router.
Now you can configure client machines on the 192.168.1.0 network. Be sure to use 192.168.1.1 as the default gateway and 69.30.0.200 as the primary nameserver.
After a client is properly configured it should be able to ping the routers ethernet interface (192.168.1.1) and any InterNet host. Note: You will NOT be able to ping the router or any host on it's ethernet from the InterNet.
Copyright © 1998 - 2002 EasyStreet Online Services, Inc. All rights reserved.
EasyStreet and the EasyStreet logo are registered trademarks of EasyStreet Online Services. Certain other names, logos, designs, titles, words or phrases on this site may constitute trademarks, servicemarks or tradenames of EasyStreet or other entities which may be registered in certain jurisdictions.