NETOPIA R5300 FRAME RELAY ROUTER

EasyStreet > Support > Routers > Netopia R5300 Frame Relay Router > Configure NAT Off

The following assumptions are made regarding the setup instructions on this page:

• The router is running firmware version 4.10 or higher.

COMMUNICATING WITH THE ROUTER
There are 2 ways to connect to the Netopia router:

• SERIAL CONNECTION - This is the preferred connection.  In the box that the Netopia came in, there is a bag with a serial cable.  One end of it connects to an available COM port on your machine.  The other end connects to the CONSOLE port on the back of the Netopia.  Please reference the Netopia manual for further details.
• TELNET CONNECTION - Out of the factory, the Netopia's LAN IP is set to 192.168.1.1.  You can telnet to this IP using your preferred telnet program.  This method assumes knowledge of putting the computer you're telnetting from on the same network as the Netopia's LAN IP, including connecting the proper CAT5 ethernet cables from your computer to the Netopia's hub.  Please consult your network administrator for further details.

OBJECTIVE:
The screens below will show you how to configure the router using information EasyStreet has provided you.

NOTE:
This configuration assumes that you are getting more than one public IP from EasyStreet and that the router will NOT use NAT.  For instructions on how to configure the router if you are only getting one public IP from EasyStreet, check the index page.

CONFIGURING THE ROUTER

01.  From the MAIN MENU highlight "Easy Setup..." and hit the ENTER key.

02.  The following fields in the screen above are described below.

• Operation Mode... - Leave unchanged as "Normal".
• Line Encoding... - Leave unchanged as "B8ZS".
• Framing Mode... - Leave unchanged as "ESF".
• Number of DS0 Channels: - This is the number of channels that need to be turned on for the speed of your frame.  The example above using "2" states that this is a 128kbframe circuit.  The table below shows the proper settings per speed:
  
      2 = 128kb
      4 = 256kb
      6 = 384kb
      8 = 512kb
     24 = Full T1
   
• First DS0 Channel: - Leave unchanged as "1".
• Contiguous Channels: - Leave unchanged as "Yes".
• Channel Data Rate... - Leave unchanged as "Nx64k".
• Data Link Encapsulation... - Leave unchanged as "Frame Relay".
• PPP over Frame Relay Enabled: - Leave unchanged as "Off".

03.  Highlight "NEXT SCREEN" and hit the ENTER key.

04.  The following fields in the screen above are described below.

• Connection Profile Name: - Leave unchanged as "Easy Setup Profile".
• Address Translation Enabled: - Set to "No".
• IP Addressing... - Leave unchanged as "Numbered".

• Local WAN IP Address: - This is your IP address.  It is in the configuration sheet from EasyStreet under the heading "Serial IP Addressing" called "Customer Serial IP:"

• Local WAN IP Mask: - This is the subnet mask associated with the CUSTOMER SERIAL IP.  It is in the configuration sheet from EasyStreet under the heading "Serial IP Addressing" called "Netmask:".

• Frame Relay Management Type... - Leave unchanged as "ANSI (Annex D)".

05.  Highlight "NEXT SCREEN" and hit the ENTER key.

06.  The following fields in the screen above are described below.

• Ethernet IP Address: - The table below is the same table you have in the configuration sheet EasyStreet sent you.  The numbers shown below are for example only.
  
  ----------------------------------------------------- Ethernet IP Addressing -            

  IP Address Type	: /29 Class-C Network
  Number of Hosts	: 6
  Domain Name	: domain.com
  Network Number	: 111.22.333.44
  Customer IP Addresses	: .46 thru .50
  Netmask	: 255.255.255.248
  Broadcast Address	: 111.22.333.51
  Router Ether IP Address	: .45

  In the example above, "111.22.333.45" is the IP address you'd enter in this field.  You would replace the default 192.168.1.1 IP address.
   

• Ethernet Subnet Mask: - This is the subnet mask associated with the network above.  It is in the configuration sheet from EasyStreet under the heading "Ethernet IP Addressing" called "Netmask:".
• Domain Name: - Leave blank.
• Primary Domain Name Server: - Set to "69.30.0.200".
• Secondary Domain Name Server: - Set to "209.162.195.5".
• Default IP Gateway: - This is the IP address on the EasyStreet side of the connection.  It is in the configuration sheet from EasyStreet under the heading "Serial IP Addressing" called "EasyStreet Serial IP:".
• IP Address Serving: - Set to "Off".

07.  Highlight "NEXT SCREEN" and hit the ENTER key.

08.  The following fields in the screen above are described below.

• Write Access Name: - This is the username that will be used for security access to the Netopia router.  Enter in your choice of username.  EasyStreet uses "admin" as a default.
• Write Access Password: - This is the password associated with the above username.  Enter in your choice of password.

09.  Highlight "RESTART DEVICE" and hit the ENTER key.

WHEN THE ROUTER RESTARTS, AND THE READY LIGHT TURNS SOLID GREEN ON THE FRONT OF THE ROUTER, IT IS READY FOR USE.

BACK TO THE NETOPIA R5300 INDEX

Copyright © 2002 EasyStreet Online Services, Inc. All rights reserved.
EasyStreet and the EasyStreet logo are registered trademarks of EasyStreet Online Services. Certain other names, logos, designs, titles, words or phrases on this site may constitute trademarks, servicemarks or tradenames of EasyStreet or other entities which may be registered in certain jurisdictions.